BLTouch auto leveling sensor from ANTCLABS - FREE SHIPPING!
4220
Sold Out
FREE SHIPPING ON THIS ITEM!
This is our favorite
auto-leveling sensor !!!
This is THE original BLTouch sensor from ANTCLABS .
ElectronicGeek.ca is a prould official reseller.
BLTouch is an auto leveling sensor for 3D Printers based on open-source.
- Simple, Smart, High-precision
- It could work with any kinds of bed materials, such as glasses, woods, metals, and so on.
Main functions and controls of BLTouch are same as usual auto bed leveling sensor, consists of RC servo and micro switch.
Main functions and controls of BLTouch are same as usual auto bed leveling sensor, consists of RC servo and micro switch.
Thus, BLTouch can be applied on almost every board.
BLTouch fulfilled simple structure and high precision by using progressively designed solenoid and hall sensor, and aimed user convenience and enjoyable printing by adding many smart functions, self-test, alarm, alarm release, test mode for M119.
Simple
-
BLTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because BLTouch works as usual auto bed leveling sensor.
Smart
- Self-test : The push pin is operated three times to test when the power is on
-
Alarm : The LED light blinks if a problem found on a self-test or on an operation
BLTouch consists of Atmel ATtiny13A, solenoid, and a push pin.
Innovative Solenoid : Ultra Power Saving
On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.
Low power consumption even further drops joule heating, preventing from heat problem.
Hall Sensor : Free Bed Selection
BLTouch does not uses either optical, nor proximity(inductive/capacitive) sensor.
BLTouch is controlled by hall effect, providing high precision. Thus the bed material can be selected freely.
Optimized structure : Larger Build Size
BLTouch is a small, and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor
High-precision
- BLTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise.
More technical info here : https://www.indiegogo.com/projects/bltouch-auto-bed-leveling-sensor-for-3d-printers#/
Customer Reviews
Related Items
DHT 11 Digital Temperature and Humidity Sensor for Arduino Raspberry pi
$3.00 $6.00
1.DHT series numeric humiture sensor. 2.Humidity measuring range: 2090%RH(050temperature compensation). 3.Temperature measuring range: 0+50. 4.Humidity measurement accuracy: 5.0%RH. 5.Temperature measurement accuracy: 2.0. 6.response time: <5s. 7.low power consumption. 8.Size:2.3cm x...
5V 16 Channels Relay Module Shield for Arduino ARM PIC AVR DSP ( 16 channel )
$26.00
Features: 5V 16-Channel Relay interface board, and each one needs 50-60mA Driver Current.Equiped with high-current relay, AC250V 10A; DC30V 10A.Standard interface that can be controlled directly by microcontroller (Arduino ,...
FT232RL FTDI USB 3.3V 5.5V to TTL Serial Adapter Module for Arduino Mini Port
Sold Out
Features: Brand new and high quality Chip: FT232RL Draw out all signal port of FT232RL chip. RXD/TXD transceiver communication indicator. USB power supply, can choose 5V or 3.3V ,set by jumper. With over current for protection, using 500MA self-restore fuse. Pin definition: DTR,RXD,TX,VCC,CTS,GND Pitch:2.54mm Module size:36mm(length)*18mm(width) Interface: Mini USB Package Included: 1 x New FT232RL USB To Serial Adapter Module
5V 2 Channels Relay Module Shield for Arduino ARM PIC AVR DSP ( 2 channels )
$3.00 $6.00
5V 2 Channels Relay Module Shield ： This is a 2 Channel 5V Relay interface board, Be able to control various appliances, and other equipments with large current. It can...
